آ laminated aluminum foil AA1235 is a high-purity, soft-tempered foil that is bonded with paper or polymer films to form a flexible multilayer barrier.
In other words, the aluminum web is rarely used alone. در عوض, it is combined with layers such as PET, BOPP, PE or paper so that each material contributes a specific function.
This matters because a single thin foil, although an excellent barrier, is delicate and cannot heat-seal to itself. اولین, the polymer layers protect the soft metal from abrasion and punctures.
بعد, the inner seal layer allows the pack to be closed on standard filling equipment. سرانجام, the printed outer layer carries the brand identity that buyers see on the shelf.
This guide explains how the composite is built, why alloy 1235 is chosen for the core, and how the layers are bonded without delamination.
It also covers barrier performance, common structures, برنامه های کاربردی, specifications and the documents a buyer should verify.
A deeper technical view of the same material is available on our 1235 aluminum foil as the core layer in food composite films page.
To begin with, lamination is the process of bonding two or more flexible webs into one continuous material.
The webs are joined with adhesive, extrusion coating or heat, and they then run through the converter as a single film.
For packaging, the aluminum foil normally sits in the middle as the barrier layer.
اساساً, the construction combines materials that would be inadequate on their own. مثلا, a pure PE film is cheap and easy to seal but leaks oxygen and moisture.
By contrast, a thin aluminum foil blocks light, gas and vapor almost completely, yet it tears easily and cannot be heat-sealed without a polymer face. از این رو, joining the two creates a web that is both protective and practical.
در عمل, the converter chooses the stack before production. Each layer is specified by material, thickness and surface treatment, and the finished roll is tested for bond strength and barrier.
در نتیجه, the buyer receives a ready-to-run web rather than separate components.
آلیاژ 1235 belongs to the 1xxx series of industrial pure aluminum. In this series, the aluminum content is at least 99.35 percent, and only small amounts of iron, silicon and other trace elements remain.
That high purity gives the foil its characteristic softness and clean, bright surface.
In the soft O temper, the foil is fully annealed. در نتیجه, it is ductile and easy to fold, form and bond without cracking. It also conforms closely to the adhesive, which helps the layers grip one another.
به این دلیل, O temper is the default choice for most flexible lamination.
The surface is usually supplied with one bright side and one matt side. The bright face offers a high gloss for decorative work, while the matt face provides a uniform, low-reflection finish.
علاوه بر این, a clean, oil-free surface is essential because even a thin residue can weaken the adhesive bond.
At 2.70 g / cm3, the alloy is light, and its density stays constant across every temper. از این رو, the weight of a laminate can be estimated reliably from the foil gauge and width.
This predictability is useful when planners calculate material cost and roll length.
سرانجام, proper storage protects the material before conversion. آ laminated aluminum foil AA1235 roll should be kept dry, sealed and away from direct heat, because moisture at the edge can weaken the bond.
از این رو, warehouses control humidity and use the rolls in batch order. When these simple rules are followed, the web reaches the line in the same condition it left the mill.
Buyers often compare 1235 با 8011 و 8079 because all three are rolled into thin packaging foil. با این حال, they are not interchangeable.
The 8xxx alloys contain added iron and silicon, which make the foil stronger and stiffer. By contrast, 1235 is purer and softer, with fewer pinholes and a higher gloss.
For a flexible laminate, the softness of 1235 is usually an advantage rather than a weakness. The polymer layers provide the mechanical strength, so the foil itself does not need to be rigid.
در ضمن, its low pinhole count protects the barrier, and its bright surface supports premium printing.
That said, there are cases where an 8xxx alloy is the better fit. مثلا, a rigid container or a heavily formed lid may need the extra strength of 8011.
به همین ترتیب, a web that must withstand rough handling without polymer support may favor 8079. از این رو, the choice should follow the structure and the forming process, not price alone.
A typical composite foil is built in three functional zones. اولین, the outer layer faces the outside world and carries the print.
بعد, the core foil provides the barrier. سرانجام, the inner layer contacts the product and forms the heat seal. Each zone has a clear job, and the design only works when all three are balanced.
The outer layer is often PET, BOPP or paper. PET adds stiffness and heat resistance, while BOPP offers a crisp, glossy print surface.
Paper, از طرف دیگر, gives a natural feel and good tear behavior. In every case, the outer face also shields the soft metal from scratches.
The core is the 1235 فویل. Even at six to nine microns, a sound foil blocks nearly all light and most gas and vapor. It is the reason the laminate can protect sensitive products for long shelf periods.
Without this metal layer, the film would rely on coated polymers, which rarely match metal at the same thickness.
Barrier performance is described with two main figures. The water vapor transmission rate, or WVTR, measures moisture passage, while the oxygen transmission rate, or OTR, measures gas passage.
In a well-bonded aluminum laminate, the WVTR can fall below 0.005 g/m2/day and the OTR can approach zero.
با این حال, these figures depend on the foil being free of pinholes. As the gauge drops, the number of pinholes tends to rise, and each hole becomes a tiny leak path.
از این رو, the converter must balance thinness against defect control. در عمل, a slightly thicker foil with fewer pinholes often outperforms a thinner, cheaper web.
The inner seal layer is usually LDPE or a heat-seal coating. It melts at a controlled temperature and bonds the pack to itself or to a tray.
علاوه بر این, it separates the aluminum from acidic or salty foods, which prevents direct contact and any risk of corrosion.
Over time, a few standard stacks have become common because they cover most packaging needs. The letters name the layers from outside to inside, and the number in brackets often gives the foil gauge in microns.
به عنوان مثال, PET/AL(9)/PE means a PET outer layer, a nine-micron foil and a PE seal layer.
The PET/AL/PE stack is the most versatile option. It runs on high-speed form-fill-seal lines, tolerates retort temperatures and prints well.
For shelf-stable meals and pouches, this construction is often the first choice.
Paper/AL/PE is selected when the brand wants a paper-like texture. It is common for butter wraps, chilled products and carton liners.
در ضمن, BOPP/AL/PE is favored for snacks and confectionery because its glossy outer face makes the colors look sharp.
More specialized stacks add nylon, or PA, for puncture resistance, or use extrusion-coated LDPE for lids and insulation.
In each case, the stack is selected as a system rather than as separate layers. That discipline is what keeps the final pack reliable at high speed.
علاوه بر این, the chosen structure affects more than protection. مثلا, a simpler two-layer web uses less material and may be easier to recycle, while a heavier multilayer offers longer shelf life.
از این رو, buyers should weigh the product’s real shelf needs against material use. در عمل, over-specifying the barrier adds cost without benefit, whereas under-specifying it risks returns.
The bond between the foil and its neighbors is just as important as the materials themselves. A weak interface can open under heat, moisture or flexing, and the layers then separate.
This failure, called delamination, destroys both the appearance and the barrier.
Before bonding, the foil surface is often treated to raise its wetting tension. A higher tension lets the adhesive spread evenly instead of pulling back into droplets.
Common treatments include corona or plasma activation, which also create reactive sites on the metal.
The finished bond is checked with a peel test, which pulls the layers apart and records the force. A typical target for a high-barrier web is around three newtons per fifteen millimeters of width.
علاوه بر این, the bond should retain most of its strength after temperature cycling.
Failures usually fall into a few clear modes. Adhesive failure means the glue separates cleanly from the foil, while cohesive failure means the glue itself splits. Moisture can also enter the interface and weaken the bond.
از این رو, a stable laminate needs clean surfaces, the correct adhesive and controlled residual stress.
Our own technical note on 1235 aluminum foil composite flexible packaging describes how treated samples retain over ninety percent of their bond strength after environmental cycling.
That kind of retention is the practical mark of a stable interlayer.
The same 1235 laminate family serves a surprisingly wide range of products. The gauge and stack are adjusted to the product, the filling temperature and the required shelf life. Below are five areas where the material is commonly used.
Pouches, sachets and stand-up packs use the standard PET/AL/PE or BOPP/AL/PE stack. The metal layer protects flavor and aroma, while the seal layer runs on form-fill-seal equipment. For snacks, coffee, spices and powdered foods, this is the core application.
Retort pouches and lidding webs must survive sterilization at roughly 121 به 130 درجه سلسیوس. The soft foil tolerates this heat without losing its barrier, and the outer PET layer keeps its shape. A related family of coated webs is explained on our 8011 aluminum foil for dairy packaging page.
Cigarette packs and premium labels value the bright, printable face of 1235. The foil is often laminated with paper or a thin polymer, and it supports fine embossing and metallic effects. Here, the decorative role is as important as the barrier.
In cables and building insulation, the foil is laminated with PET or LDPE to shield against moisture and electromagnetic interference. The composite is flexible enough to wrap around conductors, and the polymer face adds tear resistance. These industrial webs often use wider rolls.
Battery and capacitor applications rely on the clean surface and consistent gauge of pure foil. The same lamination principles support tape, shielding and electronic barrier webs. A related blister construction is shown on the PTP blister aluminum foil page.
A laminated aluminum foil AA1235 order can be customized across gauge, عرض, structure and surface. The table below summarizes the common ranges, although special requests can often be arranged.
Buyers should confirm the exact figures at the inquiry stage.
The gauge is the main driver of material cost because it sets the amount of aluminum. با این حال, a very thin web can raise processing risk and increase waste.
از این رو, the total cost should include running performance and reject rate, not only the price per kilogram.
بعلاوه, tolerance control deserves attention. A consistent gauge and width keep the web centered on high-speed machines, and a stable core diameter prevents sudden tension changes.
در نتیجه, rolls that meet tight tolerances produce fewer stops and less waste. در این حالت, the supplier’s measurement records are as valuable as the nominal figures.
شرکت آلومینیوم هنان هواوی, Ltd. is an aluminum foil manufacturer based in the Gongyi aluminum cluster in Henan, چین.
The company was founded in 2001 and operates integrated rolling, به پایان رساندن, slitting and coating capacity for packaging foil.
The site covers roughly 250,000 square meters with about 1,200 people and an annual capacity of more than 200,000 تن.
The foil is exported to more than seventy countries, which means the documentation and packaging are aligned with international practice.
For lamination customers, HWALU can supply 1235 in the soft temper with custom gauge, width and surface treatment.
Each batch is supported by mill test certificates and traceable batch marks. علاوه بر این, the technical team reviews drawings or a sample before production, so the specification is agreed in writing.
The practical benefit is repeatable conformity. Rather than renegotiating the standard on every order, the buyer works against one approved specification and can compare incoming rolls directly with earlier shipments.
That consistency is especially valuable for long-term repeat supply.
س: Is the foil supplied as a finished laminate or as a bare roll?
آ: Both are possible. HWALU can supply bare 1235 foil for a converter to laminate, or a finished multilayer web ready to run on a packaging line. The scope should be stated at the inquiry stage.
س: Which thickness is normal for a 1235 laminate?
آ: Thin packaging webs commonly use six to nine microns, while the full laminated range runs from about 5.5 to thirty microns. The exact gauge depends on the barrier target, pinhole requirement and line speed.
س: Can the foil touch food directly?
آ: In a laminate, the food normally contacts the PE seal layer rather than the metal. The construction is supported by food-contact documentation and migration testing, and the alloy itself is non-toxic.
س: How is delamination prevented?
آ: The foil surface is treated for wetting, the correct adhesive is selected and the bond is checked with peel tests. A stable web retains most of its bond strength after heat and moisture cycling.
س: چه فرقی با هم دارند 1235 و 8011?
آ: 1235 is a high-purity, soft 1xxx alloy with few pinholes and a bright finish, در حالی که 8011 is an Al-Fe-Si alloy with greater strength and rigidity. Soft 1235 is preferred for flexible laminated cores.
س: Which documents should accompany an export order?
آ: A mill test certificate, packing list, commercial invoice and batch traceability marks should be provided. Food-contact or barrier test reports can be added when the application requires them.
به طور کلی, a laminated aluminum foil AA1235 is a carefully designed multilayer system rather than a simple coated metal.
The soft 1235 core supplies the barrier, the outer layer carries print and protection, and the seal layer closes the pack on standard equipment.
Choosing the right specification means balancing gauge, pinholes, structure, peel strength and machine behavior.
Buyers who verify the supplier’s documents, approve a first article and keep traceable batch records remove most of the avoidable risk.
In the end, that disciplined approach is what keeps a flexible package fresh, safe and consistent from the first trial to long-term repeat supply.
When the layers are chosen as one system, the laminate performs reliably at high speed and protects the product throughout its shelf life.
شرکت آلومینیوم هنان هواوی, Ltd. رهبر بسیاری از تولید کنندگان و تامین کنندگان آلومینیوم در چین است. ما به شدت کیفیت را کنترل می کنیم و بر مشتریان تمرکز می کنیم. ما امیدواریم که همکاری عمیقی با شما داشته باشیم و خدمات سفارشی OEM محصولات آلومینیومی با کیفیت بالا را به شما ارائه دهیم. اگر می خواهید جدیدترین و بهترین قیمت ها را بر حسب کیلوگرم یا هر تن وزن استاندارد دریافت کنید, لطفا با ما تماس بگیرید.