aluminum foil jumbo roll

Aluminum foil jumbo roll

Aluminum foil parameters Raw Material 1235, 3003, 8011 etc Alloy Temper O, H28, etc Thickness 6.5 micron, 10 microns, 11micron( 11 microns), 20micron, 130-250mic ( for laminated foil cold forming ) Size 3000m, 80 cm, etc We can provide jumbo roll aluminum foil Product Name Alloy Temper Thickness or Gauge(mm ) Width(mm ) Surface Finishing Use Aluminum Foil For Foo ...

1235 aluminum foil

1235 alloy aluminum foil

Mechnical Properties Dinomination Gauge/Thickness (mm) Alloy Temper Tensile Strenght (MPa) Elogation (%) Food Container Foil 0.041 – 0.089 1235-O 45 – 100 >4 0.09 – 0.139 50 – 100 >6 0.14 – 0.20 50 – 100 >10 Application Food container etc

1200 aluminum foil

1200 alloy aluminum foil

1200 aluminum foil details Alloy 1200 aluminum foil Temper F, O,H12,H16,H18,H22,H24,H26 Thickness 0.3-15mm Width*Length (10-1600mm)*C 1200 alloy aluminum foil parameters Chemical Composition of Alloy 1200 aluminium foil Si+Fe Cu Mn Zn Ti Mg Cr Other Al ≤1.0 ≤0.05 ≤0.05 ≤0.1 ≤0.05 - - 0.05(each) 0.15(total) 99.00 Mechanical propertiesof ...

aluminum foil pots

Aluminum foil for pot

Parameters of aluminum foil for pot container foil Alloy status 8011-H24, 3003-H24, 8011-H22 Typical thickness 0.02~0.20mm Processing method stamping forming Application of Aluminum foil for pot Aluminum foil production process

industrial aluminum foil roll

Aluminum foil for industrial use

Parameters of industrial grade aluminum foil Alloy: 3003, 8011 etc Applications of industrial used aluminum foil Insulation, low temperature resistant, al pe laminited for packing, beverage industrial use and wine use etc

The cause of pinhole in aluminum foil production process?

Aluminum foil pinhole has two main factors, one is the material, the other is the processing method. 1. Improper material and chemical composition will lead to a direct impact on the pinhole content of fake aluminum foil Fe and Si. Fe>2.5, Al and Fe intermetallic compounds tend to form coarse. Aluminum foil is prone to pinhole when calendering, Fe and Si will interact to form a firm compound. The number of ...

Selection principle of aluminum foil pass processing rate

The selection principle of pass processing rate is as follows: (1) Under the premise that the equipment capacity allows the rolling oil to have good lubrication and cooling performance, and can obtain good surface quality and shape quality, the plasticity of the rolled metal should be fully utilized, and the large pass processing rate should be used as much as possible to improve the rolling mill Production ef ...

The aluminum foil rolling mill back-up roll bearing and inner ring are successfully developed

In recent years, Huawei Aluminum Co., Ltd. has set up a special research team under the condition that the aluminum foil rolling mill backing roll and the inner ring of the backing roll bearing are tight, to maintain production by repairing the scrapped backing rolls, and to ensure the normal operation of the seven aluminum foil rolling mills. During the repair process, the research team was able to repair, explo ...

How is aluminum foil produced?

Cast-rolled aluminum foil production process Aluminum liquid, aluminum ingot -> Smelt -> Continuous roll casting -> Winding -> Cast roll finished product Plain foil production process Plain foil -> Cast-rolled coil -> Cold rolled -> Foil rolling -> Slitting -> Annealing -> Plain foil finished product The manufacture of aluminum foil is similar to making pasta at home. A large b ...

The application potential of aluminum foil in lithium batteries is huge

The development of new energy vehicles is an important part of the low-carbon economy, and plays an important role in alleviating the contradiction between energy supply and demand, improving the environment, and promoting sustainable economic development. New energy vehicles are one of the industries that best reflect a country's technological development level, independent innovation capabilities and internatio ...

Professional knowledge of tension system of aluminum foil slitting machine

After printing and coating, aluminum foil paper and cash register paper need to be post-printed and slit on a slitting machine to cut large rolls of semi-finished products into the required specifications. The semi-finished products that run on the slitting machine are an unwinding and rewinding. This process includes two parts: machine speed control and tension control. The so-called tension is to pull the al ...