food aluminum foil roll

Aluminum foil for food

Parameters Alloy: 1235, 8011 etc Application: food-grade packaging bag, food wrapping etc Food grade aluminum foil is mainly used for food and quasi-food packaging, the thickness is 0.015, 0.012, 0.009, 0.007 microns, and the aluminum alloys are 1145, 1235, 1100, 3003, 8011, 8079, and so on. The performance requirements for food-grade aluminum foil are strict because it is connected to the food directly. ...

8011 aluminum foil

8011 alloy aluminum foil

Introduction of 8011 alloy aluminum foil 8011 alloy aluminum foil is added Al-Fe-Si elements, more than 1% of the total alloying elements in the corresponding performance of its alloy has a higher advantage, mainly for food packaging, and pharmaceutical packaging. Machinable range of thickness: 0.02mm-0.07mm, width 300mm-1100mm, can be customized according to customer needs. General parameters of aluminu ...

PTP aluminum blister foil

PTP aluminum Blister foil parameter Alloy 1235, 8011, 8021 etc Temper  O( HO ), H18, etc Width 300mm, 600mm, etc Thickness OP: 0.5 - 1.5 g/m2 Aluminum foil: 20 micron ( 0.02mm ), 25 micron ( 0.025mm ), 30 micron ( 0.3mm ) etc HSL ( VC ):3 - 4.5 gsm Primer: 1gsm Surface treatment Laminated, printing, Single bright side, etc what is PTP aluminum blister ...

aluminum strip foil for pills foil packaging

Easy tear aluminum strip foil for medicine

It uses two layers of medicinal strip packaging film (SP) to sandwich the medicines. The distance between the unit medicines is a certain interval. The inside of the two SP films near the medicines are heat-sealed on the strip vacuum packaging equipment. A form of unit packaging formed by pressing tooth marks in between. Strip packaging is continuous work on strip vacuum packaging equipment, which is especially s ...

roll aluminum foil wrapping

Aluminum foil for wrapping

  Application Food wrapping: chocolate, sandwich, burger etc

Aluminum foil rolling process and characteristics

In the production of double foil, the rolling of aluminum foil is divided into three processes: rough rolling, intermediate rolling, and finishing rolling. From a technological point of view, it can be roughly divided from the thickness of the rolling exit. The general method is that the exit thickness is greater than Or equal to 0.05mm is rough rolling, the exit thickness is between 0.013 and 0.05 is intermediat ...

How to distinguish between good and bad aluminum foil? Comprehensively sort out the quality defects of aluminum foil

In the production process of aluminum foil, there are multiple processes such as rolling, finishing, annealing, packaging, etc. The interlocking production process, any problem in any link may cause aluminum foil quality problems. The quality defects of the purchased aluminum foil products will not only affect the appearance, but also directly affect the quality of the products produced, and even more directly ca ...

Selection principle of aluminum foil pass processing rate

The selection principle of pass processing rate is as follows: (1) Under the premise that the equipment capacity allows the rolling oil to have good lubrication and cooling performance, and can obtain good surface quality and shape quality, the plasticity of the rolled metal should be fully utilized, and the large pass processing rate should be used as much as possible to improve the rolling mill Production ef ...

What are the causes of foil coiling defects?

Coiling defects mainly refer to loose, layer channeling, tower shape, warping and so on. Aluminum foil roll during the winding process. Because the tension of aluminum foil is limited, enough tension is the condition to form a certain tension gradient. Therefore, the winding quality ultimately depends on good shape, reasonable process parameters and suitable precision sleeve. It is ideal to obtain tight coils ...

How to choose aluminum foil for food and its advantages?

Aluminum foil has the following advantages in food packaging: Barrier property. Aluminum foil has excellent resistance to water, air (oxygen), light, and microorganisms, which are important factors in food spoilage. Therefore, aluminum foil has a good protective effect on food. Easy processing. Aluminum has a low melting point, good heat sealing, and easy molding. Can be processed into any shape according to ...

Aluminum foil production process - ingot hot rolling method, twin roll casting method

hot ingot rolling First, the aluminum melt is cast into a slab, and after homogenization, hot rolling, cold rolling, intermediate annealing and other processes, it is continued to be cold rolled into a sheet with a thickness of about 0.4~1.0 mm as a foil blank (casting → hot rolling billet → cold rolling → foil rolling). In the ingot hot rolling method, the hot rolled billet is first milled to remove defect ...